Petamo GHY 441, 443

Manufacturer: KLÜBER LUBRICATION (Germany)

High-temperature and long-term lubricant for rolling bearings subject to high loads
PETAMO GHY 443 and PETAMO GHY 441 (recommended for relubrication due to its softer consistency) are special lubricating greases based on ester oil and polyurea thickener. The greases have been especially designed for the lubrication of rolling and plain bearings subject to high loads and temperatures. Being an efficient alternative to mineral oil based products, PETAMO GHY 443 and PETAMO GHY 441 achieve a much longer service life and therefore help to reduce maintenance costs. Due to their high base oil viscosity and excellent thermal stability they are mainly used for large rolling bearings.

Benefits for your application

Tried-and-tested grease for long-term lubrication, less maintenance and high reliability
Good load-carrying capacity prevents wear, hence longer bearing life
Excellent water resistance and corrosion protection prevent premature bearing failure and help to reduce maintenance costs
Reduction in grease consumption and high resistance to oxidation and ageing due to the synthetic grease formulation

Orther products

Product

Features, Application

Klubertemp HM 83-402

High-temperature long-term greases
Klubertemp HM greases are long-term lubricating greases based on perfluoropolyether oil and PTFE which has been specifically designed for high-temperature lubrication. Owing to the base oil viscosity and the high load-carrying capacity, Klubertemp HM greases are particularly suitable for the initial and relubrication of medium-speed rolling bearings subject to high temperatures and loads.

Kluberlub PHB 71-461

High-temperature lubricating grease
Kluberlub PHB 71-461 is a special high-temperature lubricating grease based on mineral oil and polyurea. It is suitable for a wide service temperature range and can be used up to 180°C under continuous relubrication conditions. Kluberlub PHB 71-461 may be applied via centralized lubrication equipment.
Kluberlub PHB 71-461 incorporates special EP additives ensuring good wear protection under high load conditions.

Kluberlub OG 11-6000 BH

Open Gear Lubricants
Kluberlub OG 11 BH Series are Open Gear Lubricants based on mineral oil, Aluminum Complex Soap thickener and MX technology based on Organo Molybdenum Complex.
The high viscosity base fluids used in the lubricants provide extreme pressure (EP) and antiwear characteristics to the lubricant.

Kluberoil 4 UH1-1500 N

Synthetic gear and multipurpose oil for the food-processing and pharmaceutical industries
Kluberoil 4 UH1 N is a synthetic high-performance gear and multipurpose oil based on PAO satisfying the growing requirements and increasing power density of modern gears.
These are NSF H1 registered and therefore comply with FDA 21 CFR § 178.3570. The lubricants were developed for incidental contact with products and packaging materials in the food-processing, cosmetics, pharmaceutical or animal feed industries.

Klubersynth BH 72-422

High-temperature grease for slow-running bearings
Klubersynth BH 72-422 is a synthetic high-temperature grease containing ester as well as perfluorinated polyether (PFPE) oils, and a PTFE thickener.
This grease shows good oil retention at high temperature and is thermally stable, which enables Klubersynth BH 72-422 to extend your relubrication intervals at operating temperatures above 160°C up to 220°C.

Grafloscon C-SG 0 Ultra

Graphite based operational lubricant for open gear drives
Because of its unique chemical composition based on an aluminium soap thickener, the GRAFLOSCON C-SG 0 ULTRA provide good adhesion that protects the tooth flank even at extreme loads.The life of the gear is enhanced by the presence of fine graphite particles that form a protective layer and prevent damage.
The vibrations and temperature difference across the tooth flank are reduced. The gears are also protected against corrosion due to the special additives.

Technical service

Organizing technical training courses, technical workshops at customers' factories

Lubrication consultation and recommendation

Automatic lubrication system design and installation

Gap measurement in vertical grinding machine

Repair lubrication spray service

Open gear inspection and adjustment

Address: Room 503, 5^thFloor, 101 Lang Ha Building, Dong Da Dist., Hanoi, Vietnam
Phone: (+84.24) 3562 6208
Hotline: +84 911 54 2416
Email: info@vuminh.com.vn

Address: 68 Le Manh Trinh Street, Phuoc My Ward, Son Tra District, Da Nang City, Vietnam

Phone: (+84.236) 394 3203

Hotline: +84 911 57 2416

Address: Room 10, 9^thFloor, An Khang B Building, An Phu Ward, Thu Duc City, Ho Chi Minh City, Vietnam
Phone: (+84.28) 6281 3200
Hotline: +84 911 04 2416