Kluberbio LG 39-701 N

Manufacturer: KLÜBER LUBRICATION (Germany)

Eco-compatible operating lubricant for open gear drives
Kluberbio LG 39-701 N is a high-performance grease with a new type of base oil and additive package. It combines very good eco-friendliness with high load-carrying capacity, good antiwear and anticorrosive effect and excellent adhesion to surfaces.
The high-viscosity base oil of Kluberbio LG 39-701 N comes from 100 % renewable resources.
Kluberbio LG 39-701 N complies with the 2013 Vessel General Permit requirements of the Environmental Protection Agency (EPA) in terms of biodegradability, minimal toxicity and bio-accumulation to be met by Environmentally Acceptable Lubricants.
Due to the lubricant's excellent low-temperature behaviour, it can be pumped in centralised lubricating systems down to -30°C and sprayed even below 0°C. These positive product characteristics enable you to use the lubricant over a wider temperature range than is common with mineral-oil-based greases of the same base oil viscosity.

Benefits for your application

Complies with the requirements for Environmentally Acceptable Lubricants as defined in Appendix A of the EPA 2013 GP (Vessel General Permit)
Lower environmental impact in the event of leakage. The base oil consists of renewable raw materials and is ultimately biodegradable
Good low-temperature behaviour enables operation of open gear drives in cold conditions
Selected additives ensure longer component life and reduced wear
Cost reduction due to low consumption when applied by selected spraying systems
Meets requirements for OSPAR conformance, including Norway Yellow 1, Denmark (registration number 2486711) and Cefas E (registration number 27078)

Orther products

Product

Features, Application

Klubersynth GEM 4 N Series

Synthetic high-performance gear and multipurpose oil with KlüberComp Lube Technology
Klubersynth GEM 4 N is a synthetic high-performance gear and multipurpose oil based on PAO. Klubersynth GEM 4 N includes KluberComp Lube Technology, i.e. it is based on especially high-grade raw materials and advanced additives, enabling maximum performance in the lubrication of all gear components.
Klubersynth GEM 4 N is approved by Siemens-Flender, SEW, MAAG Gears, etc.

Klubersynth GH 6 Series

Synthetic high-performance gear and high-temperature oil with KluberComp Lube Technology
Klubersynth GH 6 is a synthetic high-performance gear and high-temperature oil based on polyglycol. It includes KluberComp Lube Technology, i.e. it is based on especially high-grade raw materials and advanced additives, enabling maximum performance in the lubrication of all gear components.
Klubersynth GH 6 is approved by Siemens-Flender, SEW, MAAG Gears, etc.

Kluberplex BEM 41-132

High-temperature and long-term grease for rolling bearings
Kluberplex BEM 41-132 is based on synthetic hydrocarbon oil, mineral oil and a special lithium soap. Special additives ensure optimum oxidation resistance as well as protection against wear and corrosion.

Kluberquiet BQH 72-102

High-purity rolling bearing grease for long-term lubrication
Kluberquiet BQH 72-102 is a synthetic high-temperature lubricating grease. Due to the careful selection of product components and the clean manufacturing environment, Kluberquiet It is a rolling bearing grease with a particularly low noise level. It offers excellent performance characteristics thanks to a high-quality ester oil, a new polyurea thickener and special additives. It is special in that it combines high-temperature resistance and extreme purity.

Altemp Q NB 50

Lubricating and assembly paste
ALTEMP Q NB 50 is a white/beige lubricating paste containing a mineral base oil, a barium complex soap and inorganic solid lubricants.
Besides its application as a universal assembly paste, this product offers benefits especially in friction points with small to minimum motion under high static and dynamic loads.

Kluberplex BEM 41-141

Lubricant for rolling and plain bearings subject to high loads
Kluberplex BEM 41-141 offers good pressure and wear resistance and does not contain any inorganic solid lubricants like MoS2 or graphite.
Due to its good compatibility with commercial sealing materials, the grease can be used for a wide range of applications.

Technical service

Organizing technical training courses, technical workshops at customers' factories

Lubrication consultation and recommendation

Automatic lubrication system design and installation

Gap measurement in vertical grinding machine

Repair lubrication spray service

Open gear inspection and adjustment

Address: Room 503, 5^thFloor, 101 Lang Ha Building, Dong Da Dist., Hanoi, Vietnam
Phone: (+84.24) 3562 6208
Hotline: +84 911 54 2416
Email: info@vuminh.com.vn

Address: 68 Le Manh Trinh Street, Phuoc My Ward, Son Tra District, Da Nang City, Vietnam

Phone: (+84.236) 394 3203

Hotline: +84 911 57 2416

Address: Room 10, 9^thFloor, An Khang B Building, An Phu Ward, Thu Duc City, Ho Chi Minh City, Vietnam
Phone: (+84.28) 6281 3200
Hotline: +84 911 04 2416