Kluberbio LG 39-701 N

Manufacturer: KLÜBER LUBRICATION (Germany)

Eco-compatible operating lubricant for open gear drives
Kluberbio LG 39-701 N is a high-performance grease with a new type of base oil and additive package. It combines very good eco-friendliness with high load-carrying capacity, good antiwear and anticorrosive effect and excellent adhesion to surfaces.
The high-viscosity base oil of Kluberbio LG 39-701 N comes from 100 % renewable resources.
Kluberbio LG 39-701 N complies with the 2013 Vessel General Permit requirements of the Environmental Protection Agency (EPA) in terms of biodegradability, minimal toxicity and bio-accumulation to be met by Environmentally Acceptable Lubricants.
Due to the lubricant's excellent low-temperature behaviour, it can be pumped in centralised lubricating systems down to -30°C and sprayed even below 0°C. These positive product characteristics enable you to use the lubricant over a wider temperature range than is common with mineral-oil-based greases of the same base oil viscosity.

Benefits for your application

Complies with the requirements for Environmentally Acceptable Lubricants as defined in Appendix A of the EPA 2013 GP (Vessel General Permit)
Lower environmental impact in the event of leakage. The base oil consists of renewable raw materials and is ultimately biodegradable
Good low-temperature behaviour enables operation of open gear drives in cold conditions
Selected additives ensure longer component life and reduced wear
Cost reduction due to low consumption when applied by selected spraying systems
Meets requirements for OSPAR conformance, including Norway Yellow 1, Denmark (registration number 2486711) and Cefas E (registration number 27078)

Orther products

Product

Features, Application

Kluberfluid C-F 3 Ultra

Operational lubricant for large girth gear drives
Kluberfluid C-F 3 Ultra is a lubricant of a new generation, developed specifically for the lubrication of medium-size to large girth gear drives. It is based on synthetic hydrocarbons and mineral oil. It provides good adhesion, excellent resistance to high pressure and protection against wear. This product is suitable for use at component temperatures up to 120°C.
Kluberfluid C-F 3 Ultra meets the requirements of ANSI/AGMA 9005-E02 annex D-2.

Kluberfluid D-F 1 Ultra

Repair lubricant for open girth gear drives
Klüberfluid D-F 1 ULTRA is a running-in and repair lubricant suitable for manual spray application. It is based on mineral oil thickened with lithium soap and contains special additives.

Klubersynth OA 98-15000

Operational lubricant for large gear drives
Klubersynth OA 98-15000 is based on the SLIBF concept (Solid Lubricant Integrated Base Fluid) was developed precisely to meet the high demands of open gear drives.
It provides excellent adhesion, good film formation, less splashing from the gears and reducing leakages from the gear casing. This results in better maintenance practices and increased safety. It also provides good pumpability at lower temperatures and offers low resistance to pumping the lubricant.

Grafloscon B-SG 00 Ultra

Running-in lubricant for open drives
Grafloscon B-SG 00 Ultra is a sprayable running-in lubricant with a mineral base oil. It contains aluminium stearate as a thickener and solid lubricant particles of fine graphite. The lubricant is free from bitumen, heavy metals, solvents and raw materials containing chlorine.
GRAFLOSCON B-SG 00 ULTRA reduces surface roughness and improves the tooth flank quality which makes it also suitable for corrective lubrication if tooth flanks are damaged.

Grafloscon C-SG 2000 Ultra

Operational lubricant for open drives
Grafloscon C-SG 2000 Ultra is a sprayable adhesive lubricant with a mineral base oil. It contains aluminium complex soap and solid lubricant particles of fine graphite. It is resistant to high pressure and contains antiwear additives, adhesion improvers and corrosion inhibitors. The raw materials used for the manufacture of Grafloscon C-SG 2000 Ultra are free of bitumen, solvents and chlorine.

Grafloscon C-SG 0 Ultra

Graphite based operational lubricant for open gear drives
Because of its unique chemical composition based on an aluminium soap thickener, the GRAFLOSCON C-SG 0 ULTRA provide good adhesion that protects the tooth flank even at extreme loads.The life of the gear is enhanced by the presence of fine graphite particles that form a protective layer and prevent damage.
The vibrations and temperature difference across the tooth flank are reduced. The gears are also protected against corrosion due to the special additives.

Technical service

Organizing technical training courses, technical workshops at customers' factories

Lubrication consultation and recommendation

Automatic lubrication system design and installation

Gap measurement in vertical grinding machine

Repair lubrication spray service

Open gear inspection and adjustment

Address: Room 503, 5^thFloor, 101 Lang Ha Building, Dong Da Dist., Hanoi, Vietnam
Phone: (+84.24) 3562 6208
Hotline: +84 911 54 2416
Email: info@vuminh.com.vn

Address: 68 Le Manh Trinh Street, Phuoc My Ward, Son Tra District, Da Nang City, Vietnam

Phone: (+84.236) 394 3203

Hotline: +84 911 57 2416

Address: Room 10, 9^thFloor, An Khang B Building, An Phu Ward, Thu Duc City, Ho Chi Minh City, Vietnam
Phone: (+84.28) 6281 3200
Hotline: +84 911 04 2416