Adhesive lubricant
GRAFLOSCON C-SG 500 PLUS, a sprayable adhesive lubricant based on mineral oil, is aluminium complex saponified and contains solid lubricant (fine graphite). It is resistant to high pressure and is provided with anti-wear additives, adhesion improvers and corrosion inhibitors.
GRAFLOSCON C-SG 500 PLUS is free from bitumen, solvents and lead.
Benefits for your application
Operational lubricant for open drives, sliding and guide rails, rubbing seals
No lead additives
Can be applied through automatic spraying equipment
Light-coloured running-in and correction lubricant for open gear rim/pinion drives
Kluberfluid B-F 2 Ultra is a mineral-oil-based running-in and correction lubricant especially developed for immersion, circulation or spray lubrication.
It contains special additives and surface-smoothing solid particles enhancing the running-in process, i.e. physical/mechanical material removal on new tooth flanks.
Kluberfluid B-F 2 Ultra is a fluid grease that is free of bitumen and raw materials containing solvents, heavy metals or chlorine.
Operational lubricant for large gear drives
Klubersynth OA 98-15000 is based on the SLIBF concept (Solid Lubricant Integrated Base Fluid) was developed precisely to meet the high demands of open gear drives.
It provides excellent adhesion, good film formation, less splashing from the gears and reducing leakages from the gear casing. This results in better maintenance practices and increased safety. It also provides good pumpability at lower temperatures and offers low resistance to pumping the lubricant.
Running-in lubricant for open drives
Grafloscon B-SG 00 Ultra is a sprayable running-in lubricant with a mineral base oil. It contains aluminium stearate as a thickener and solid lubricant particles of fine graphite. The lubricant is free from bitumen, heavy metals, solvents and raw materials containing chlorine.
GRAFLOSCON B-SG 00 ULTRA reduces surface roughness and improves the tooth flank quality which makes it also suitable for corrective lubrication if tooth flanks are damaged.
Graphite based operational lubricant for open gear drives
Because of its unique chemical composition based on an aluminium soap thickener, the GRAFLOSCON C-SG 0 ULTRA provide good adhesion that protects the tooth flank even at extreme loads.The life of the gear is enhanced by the presence of fine graphite particles that form a protective layer and prevent damage.
The vibrations and temperature difference across the tooth flank are reduced. The gears are also protected against corrosion due to the special additives.
Eco-compatible operating lubricant for open gear drives
Kluberbio LG 39-701 N is a high-performance grease with a new type of base oil and additive package. It combines very good eco-friendliness with high load-carrying capacity, good antiwear and anticorrosive effect and excellent adhesion to surfaces.
The high-viscosity base oil of Kluberbio LG 39-701 N comes from 100 % renewable resources.
Kluberbio LG 39-701 N complies with the 2013 Vessel General Permit requirements of the Environmental Protection Agency (EPA) in terms of biodegradability, minimal toxicity and bio-accumulation to be met by Environmentally Acceptable Lubricants.
Due to the lubricant's excellent low-temperature behaviour, it can be pumped in centralised lubricating systems down to -30°C and sprayed even below 0°C. These positive product characteristics enable you to use the lubricant over a wider temperature range than is common with mineral-oil-based greases of the same base oil viscosity.
Operational lubricant for open drives
Grafloscon C-SG 2000 Ultra is a sprayable adhesive lubricant with a mineral base oil. It contains aluminium complex soap and solid lubricant particles of fine graphite. It is resistant to high pressure and contains antiwear additives, adhesion improvers and corrosion inhibitors. The raw materials used for the manufacture of Grafloscon C-SG 2000 Ultra are free of bitumen, solvents and chlorine.
